Below is a list of the various keypad commands that are accessed beginning with the (#) symbol.
Command function
| # # | Display Mode’s Audit Count (opening count) by user key |
| # 0 | Perform administrative operations. (audit download, resync, clock set, bank user table download, etc.) |
| # 1 | Display lock code and hardware levels. |
| # 2 | Display Lock Serial Number. |
| # 3 | Display lock opening odometer (Total Audit Count) |
| # 4 | Get last close seal, based on user key’s mode |
| # 6 | Reserved. |
| # 8 | Change shelved-mode combination or bank user’s combination. |
| # 9 | Reserved. |
| # 55 | Displays a list of the last 15 error codes |
Command function/Generation 2
| # 70 | Display active modes and identification of the activating company |
| # 71 | Display the base UTC/GMT date and time |
| # 72 | Display the local date and time according to user key’s mode |
| # 73 | Display key type and key serial number for the key presented. |
| # 74 | Display door contact switch status. |
| # 76 | Display software level the mode was activated with by user key. |
| # 77 | Display internal UTC/GMT key time on DS1994 FLM and Route and DS1427 Bank keys |
| # 78 | Display last opening local date/time by user key’s mode |
| # 79 | Display activation local date/time by user key’s mode |
Note: Some displayed data will repeat until the lock powers down (after 40 seconds) or the* key is held down.
Display prompts
| OC | Dual Mode User Key – time window mismatch |
| ECF | Enter Current combination (shelved mode) |
| ENF | Enter New combination (shelved mode) |
| CNF | Confirm New combination (shelved mode) |
| CC | Confirm Combination (Bank mode) |
| ADD | Adding new user (Bank mode) |
| DEL | Deleting user (Bank mode) |
| ECC | Enter Current Combination (Bank mode) |
| ENC | Enter new Combination (Bank mode) |
| CNC | Confirm new Combination (Bank mode) |
| D35 | Delay Time 35 minutes (Bank mode) |
| SN- | Serial Number; shown after pressing #2 |
| LL- | Lock code Level; shown after #1 pressed |
| HL- | Hardware Level; shown after #1 pressed |
| AC- | Total opening Count in All modes; shown after #3 pressed |
| SC- | Seal Count** for active mode by user key; after #4 |
| SS- | Seal count** for Shelved mode by user key; after #4 |
**Seal count, Opening Count, and Audit Count are terms used interchangeably throughout the documentation
Display prompts found only on Gen 2:
| G2 | Indication during power-up of Gen2 lock firmware |
| CEC | At EC power up, alerts that Clock was reset (need clock set key) |
| CLB | Virtual Change Key for Swing and Motorized Dead Bolt |
| CLS | Clock Set operation is in process |
| RLO | Remote Lock Out; combination entry is prevented |
| C12 34 | 4-digit Close Seal |
| DLY | 5-minute Delay because of audit restrictions |
| BEC | Change Battery Notification during EC prompt |
| IFL | Single FLM Mode activated |
| 2FL | After #70 — Dual FLM Mode activated |
| IRO | After #70 — Single Route Mode activated |
| 2RO | After #70 — Dual Route Mode activated |
| IBA | After #70 — Single Bank Mode activated |
| 2BA | After #70 — Dual Bank Mode activated |
| CN | After #70 — Company Identifier that activated mode |
| BN | After #70 — USB box number that activated mode |
| UTC | After #71 — UTC/GMT date and time |
| LCL | After #72 — local date and time, based on user key’s mode |
| YR | Date being displayed, starting with Year, then Month, then Day |
| HR | Time being displayed, starting with Hour, then Minute, then Second |
| CL | After #73 -Cencon SmartKey Type |
| CS | After #73 — Cencon SmartKey Serial Number |
| OPD | After #74 — Open Door |
| CLD | After #74 — Closed Door |
| NCC | After #74 — No door Contact Connection |
| SL | After #76 — Software Level of user key’s mode that activated this lock |
| LOP | After #78 — Last Opening date and time (local), based on user key |
| ACT | After #79 — Activation date & time (local), of user key |
| UDP | Download bank users |
| UPA | Update activate |